Différences

Ci-dessous, les différences entre deux révisions de la page.

--- pinout:wemosd1 [2021/01/16 14:48] – ptitfrap
+++ pinout:wemosd1 [2021/01/16 14:55] (Version actuelle) – ptitfrap
@@ Ligne 2: / Ligne 2: @@
 {{ :pinout:esp8266-wemos-d1-mini-pinout-gpio-pin.png?600 |}}
 ^Label	^GPIO	^Input	^Output	 ^Notes^
-|D0	|GPIO16	|no interrupt	|no PWM or I2C support	|HIGH at boot \\ used to wake up from deep sleep|
+|  D0  |GPIO16	|no interrupt|no PWM or I2C support	|<color white/orange>HIGH at boot</color> \\ used to wake up from deep sleep|
-|D1	|GPIO5	|<color white\green>OK</color>	|OK	|often used as SCL (I2C)|
+|  D1  |GPIO5	|<color white/green>OK</color>|<color white/green>OK</color>|often used as SCL (I2C)|
-|D2	|GPIO4	|OK	|OK	|often used as SDA (I2C)|
+|  D2  |GPIO4	|<color white/green>OK</color>|<color white/green>OK</color>|often used as SDA (I2C)|
-|D3	|GPIO0	|pulled up	|OK	|connected to FLASH button \\ boot fails if pulled LOW|
+|  D3  |GPIO0	|pulled up|<color white/green>OK</color>|connected to FLASH button \\ boot fails if pulled LOW|
-|D4	|GPIO2	|pulled up	|OK	|HIGH at boot \\ connected to on-board LED \\ boot fails if pulled LOW|
+|  D4  |GPIO2	|pulled up|<color white/green>OK</color>|<color white/orange>HIGH at boot</color> \\ connected to on-board LED \\ boot fails if pulled LOW|
-|D5	|GPIO14	|OK	|OK	|SPI (SCLK)|
+|  D5  |GPIO14	|<color white/green>OK</color>	|<color white/green>OK</color>	|SPI (SCLK)|
-|D6	|GPIO12	|OK	|OK	|SPI (MISO)|
+|  D6  |GPIO12	|<color white/green>OK</color>	|<color white/green>OK</color>	|SPI (MISO)|
-|D7	|GPIO13	|OK	|OK	|SPI (MOSI)|
+|  D7  |GPIO13	|<color white/green>OK</color>	|<color white/green>OK</color>	|SPI (MOSI)|
-|D8	|GPIO15	|pulled \\ to GND	|OK	|SPI (CS) \\ Boot fails if pulled HIGH|
+|  D8  |GPIO15	|pulled \\ to GND	|<color white/yellow>OK</color>|SPI (CS) \\ Boot fails if pulled HIGH|
-|RX	|GPIO3	|OK	|RX pin	|HIGH at boot|
+|  RX  |GPIO3	|<color white/yellow>OK</color>|<color white/red>RX pin</color>|<color white/orange>HIGH at boot</color>|
-|TX	|GPIO1	|TX pin	|OK	|HIGH at boot debug output at boot \\ boot fails if pulled LOW|
+|  TX  |GPIO1	|<color white/red>TX pin</color>|<color white/yellow>OK</color>	|<color white/orange>HIGH at boot</color> \\ debug output at boot \\ boot fails if pulled LOW|
-|A0	|ADC0	|Analog Input	|X	|
+|  A0  |ADC0	|<color white/green>Analog Input</color>	|<color white/red>X</color>|
 [[https://randomnerdtutorials.com/esp8266-pinout-reference-gpios/|Source]]